We've stumbled upon this post about Installing A Bathtub down the page on the net and think it made perfect sense to relate it with you here.
Installing a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is readily available, the task can move rapidly; if you have to open up a wall to eliminate the old bathtub and also position the new bath tub, the task is much harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to leave the old bathtub and set in the brand-new one. See to it you have qualified on your own for the work as well as fit trying it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to consider utilizing one before you start. Opportunities are you may require a specialist plumber to make tube links.
This article will assist you set up a brand-new bath tub in your washroom if you have actually currently bought a brand-new bathtub and also do not require to change the arrangement of your previous supply of water pipes.
Your tools as well as product list must make up the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic because of the restricted gain access to that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bath tub until the spirit level checks out level.
To set up faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Activate the water and check all joints and new pipework for leaks and tighten them if required. Fill up the tub as well as also check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait till the bathtub has been used at least once as this will settle it into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the faucet and also the sink. Safeguard the faucet in place with the producer offered backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type must be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and installations. They are offered in tubes as well as cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is recommended to fit the floor tiles utilizing waterproof or waterproof glue and cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Hopefully you enjoyed our piece on How to Install a Bathtub. Thanks for taking time to read our blog. Sharing is caring. Who knows, you might be helping someone out. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Request Your Service